Tech Applications
Tech Applications
Tech Applications

Slkor S2MF Rectifier Diode: 1000V Voltage Rating 2.0A SMAF Surface‑Mount General‑Purpose Rectifier Diode

2026-11-18 108
Slkor S2MF belongs to the S2AF-S2MF series of surface-mount general-purpose rectifier diodes and is packaged in SMAF surface-mount housing with glass-passivated chip. It offers 1000V repetitive peak reverse voltage and 2.0A average forward rectified current at base-plate temperature of 75℃, together with high resistance to forward surge current. Its plastic package meets UL94V-0 flammability standard and is optimized for automated assembly. Unless otherwise noted, all electrical parameters are measured at 25℃ ambient temperature for various surface-mount rectifier applications.

Slkor S2MF Rectifier Diode: 1000V Voltage Rating 2.0A SMAF Surface‑Mount General‑Purpose Rectifier Diode
Slkor S2MF Rectifier Diode Product Photo

I. Core Product Parameters

  1. Voltage specifications: Repetitive peak reverse voltage 1000V; maximum RMS voltage 700V; maximum DC blocking voltage 1000V.
  2. Current specifications: Average forward rectified current 2.0A at base-plate temperature of 75℃. Per JEDEC standard, peak forward surge current reaches 60.0A under single half-sine-wave of 8.3 ms. DC reverse current is 5.0μA at 25℃ with rated DC blocking voltage, and 50.0μA at 100℃ with rated DC blocking voltage.
  3. Electrical characteristics: Maximum instantaneous forward voltage 1.1V at forward current of 2.0A; typical junction capacitance 30.0pF.
  4. Thermal and temperature specifications: Typical junction-to-ambient thermal resistance 50.0℃/W. Operating junction and storage temperature range: -65℃ to +150℃.
  5. Package and soldering specifications: SMAF surface-mount package. Terminals can withstand soldering at 260℃ for 10 seconds. Plastic package meets UL94V-0 flammability classification.

Supplementary test notes: Junction capacitance is tested at 1 MHz with 4.0 V DC reverse bias. Thermal resistance is measured on PCB with 5.0×5.0 mm copper pad. Working current shall be derated by 20% for capacitive-load applications. Standard parameters are measured at 25℃ ambient temperature for 60 Hz single-phase half-wave resistive or inductive loads.

II. Key Product Features

  1. SMAF surface-mount package with built-in strain-relief structure, suitable for automated pick-and-place assembly.
  2. Plastic housing certified to UL94V-0 flammability grade to improve overall equipment safety.
  3. Glass-passivated chip junction achieves low reverse leakage current.
  4. High forward surge-current capability to resist short-duration large-current transients.
  5. Excellent high-temperature soldering performance; terminals can sustain 260℃ for 10 seconds during reflow soldering process.

III. Main Application Fields

  1. Secondary rectifying circuits of switching power supplies and AC-input half-wave rectifier circuits.
  2. Rectifying units inside power adapters and battery chargers.
  3. Surface-mount rectifier modules for industrial control circuit boards.
  4. Power conversion circuits for different consumer electronic devices.
  5. 60Hz single-phase half-wave rectification for resistive and inductive loads.

IV. Engineering Design Recommendations

  1. Current derating: When ambient temperature rises above 75℃, the allowable average forward operating current must be reduced following the device derating curve. For capacitive-load circuits, an additional 20% derating on operating current is required.
  2. Soldering control: In reflow soldering process, the maximum terminal temperature shall not exceed 260℃, and high-temperature duration shall be kept within 10 seconds to prevent device damage.
  3. PCB layout suggestion: Use 5.0×5.0 mm copper pads on printed circuit boards to achieve datasheet-specified thermal-resistance performance, enhance heat dissipation and lower device junction temperature.
  4. Surge-current evaluation: Where short-time impulse current exists in circuit, actual impulse current must not exceed rated forward surge-current value. Further surge-current derating is required under repeated cyclic-shock operating conditions.
  5. Temperature-limit management: Operating junction temperature shall not go beyond 150℃, while minimum storage and operating temperature shall stay above -65℃. Sufficient temperature margin should be reserved at design phase.

V. Product Summary

Slkor S2MF is a surface-mount general-purpose rectifier diode in SMAF package, featuring 1000V high reverse-voltage rating and 2.0A rated average forward current. Its glass-passivated chip delivers low reverse leakage current. The package fits automated production lines and provides reliable soldering heat resistance. With balanced voltage-withstand, current-handling and surface-mount advantages, it is widely used for rectification in switching power supplies, consumer electronics and industrial control equipment. In real-world engineering practice, current derating and PCB thermal design based on ambient temperature and load types are essential for long-term stable device operation。

About Slkor:

SLKOR's product portfolio includes discrete semiconductor devices such as diodes, transistors, and power devices, as well as integrated circuits such as linear regulators, DC-DC converters, interface chips, Hall sensors, ADCs, and battery management systems (BMS)


S2MFTo Product Page
whatsapp

Service Hotline

tel: +86 755 83044319

WhatsApp

Whatsapp:+8618073002950